Ryobi RTS30 Instrukcja Operatora

OPERATOR’S MANUAL10 in. TABLE SAWRTS10SAVE THIS MANUAL FOR FUTURE REFERENCEYour table saw has been engineered and manufactured to our high standard fo

10FEATURESPRODUCT SPECIFICATIONSBlade Arbor ...5/8 in.Blade Diameter ...

11KNOW YOUR TABLE SAWSee Figure 2.The safe use of this product requires an understanding of the information on the tool and in this operator’s manual

12FEATURESOPERATING COMPONENTSThe upper portion of the blade projects up through the table and is surrounded by an insert called the throat plate. The

13The following tools (not included or drawn to scale) are needed for assembly and making adjustments:TOOLS NEEDEDFEATURESBLADESFor maximum performa

14LOOSE PARTSThe following items are included with the table saw: A. Anti-Kickback Pawls ... 1 B. Bla

15The following items are included with the table saw leg stand:Fig. 6 LOOSE PARTSABEGCHIABCDDEFFEHHHIII A. Lower Brace ...

16ASSEMBLYUNPACKINGThis product requires assembly. Carefully lift saw from the carton and place it on a level work surface. NOTE: This tool is heav

17TO ASSEMBLE THE LEG STANDSee Figure 7.Assembly is best done in the area where the saw will be used. If you are unsure about the description of any p

18ASSEMBLYTO INSTALL THE HANDLESee Figure 9. Hold the nylon nut securely and turn the screw counter- clockwise to remove the nut completely. NOTE:

19ASSEMBLYIN “UP” POSITION FOR THROUGH CUTTINGIN “DOWN” POSITION FOR NON-THROUGH CUTTINGRELEASE LEVER (LOCKED)Fig. 12 RELEASE LEVER (UNLOCKED)TO CHAN

2TABLE OF CONTENTS Introduction ...

20ASSEMBLYTO CHECK SAW BLADE INSTALLATIONSee Figure 13.CAUTION: To work properly, the saw blade teeth must point down toward the front of the saw. Fai

21ASSEMBLYTO INSTALL THE BLADE GUARD AND ANTI-KICKBACK PAWLSSee Figures 14 - 16.WARNING:Replace dull or damaged anti-kickback pawls. Dull o

22ASSEMBLYTO CHECK AND ALIGN THE SPREADER/RIVING KNIFE AND SAW BLADESee Figures 17 - 18. To check alignment of the spreader/riving knife: Unplug th

23PUSH STICK STORAGESee Figure 19. Insert the push stick storage screws from the loose parts bag into the holes on the side of the saw table. Use a

24OPERATIONWARNING:Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is suf-cient to inict sev

2518 1/2 in.1/2 in.4 1/4 in.OPERATIONCUTTING AIDSSee Figure 20.Push sticks are devices that may be used for pushing a workpiece through the

26Fig. 24PUSH BLOCKFEATHERBOARDPUSH STICKBEVEL LOCKING LEVERFEATHERBOARDA featherboard is a device used to help control the workpiece by ho

27OPERATIONBEVEL RIP CUT RIP CUTCROSS CUTMITER CUTCOMPOUND (BEVEL) MITER CUT BEVEL CROSS CUT126453Fig. 25TYPES OF CUTSSee Figure 25.There are six basi

28OPERATIONTO CHANGE BLADE DEPTHSee Figure 26.The blade depth should be set so that the outer points of the blade are higher than the workpiece by app

29OPERATIONFRONT RAILFig. 29WARNING:To reduce the risk of injury, always make sure the rip fence is parallel to the blade before beginning any operati

3WARNING:Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, re and/or serious perso

30TO USE THE MITER GAUGESee Figure 30.The miter gauge provides greater accuracy in angled cuts. For very close tolerances, test cuts are recommended.T

31OPERATIONHEELING (PARALLELING) THE BLADE TO THE MITER GAUGE GROOVESee Figures 32 - 34.WARNING:The blade must be parallel to the miter gauge groove s

32OPERATIONMAKING CUTSThis table saw can perform a variety of cuts that are not all mentioned in this manual. DO NOT attempt to make any cuts not cove

33MAKING A RIP CUTSee Figure 37.WARNING:Make sure the blade guard assembly is installed and working properly to avoid serious possible injury.

34BEVEL CROSS CUTBLADE ANGLEDMITER GAUGE STRAIGHTMAKING A BEVEL CROSS CUTSee Figures 39 - 40.WARNING:Make sure the blade guard assembly is inst

35 Position the workpiece at on the table with the edge ush against the rip fence. Let the blade build up to full speed before feeding the workpi

36OPERATIONMAKING A NON-THROUGH CUTSee Figure 43.WARNING: DO NOT install dado blades on this machine. The arbor shaft has insufcient threads to

37ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the OFF position. Fa

38ADJUSTMENTSFig. 48Fig. 490° ADJUSTMENTSCREW45° ADJUSTMENT SCREWCOMBINATION SQUAREBLADEBEVEL INDICATORBEVEL LOCKING LEVERBEVEL HANDLE45° COMBINATION

39ADJUSTMENTSBLADERIP FENCELOCKING LEVERBOLTSTO CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADESee Figure 50. Unplug the saw. Raise the lockin

4GENERAL SAFETY RULES BLADE COASTS AFTER BEING TURNED OFF. NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fu

40TROUBLESHOOTING PROBLEM CAUSE SOLUTIONExcess vibration.Rip fence does not move smoothly.Rip fence does not lock at rear.Cutting binds or burns w

41TROUBLESHOOTING PROBLEM CAUSE SOLUTIONAdjust positive stops.Adjust the miter gauge.Clean the gears or screw post.Plug in motor cord or wall cord

42987000-8641-18-10 (REV:05)OPERATOR’S MANUAL10 in. TABLE SAW RTS10WARNING:Some dust created by power sanding, sawing, grinding, drilling, and other c

5SPECIFIC SAFETY RULES NEVER perform any operation “freehand” which means using only your hands to support or guide the workpiece. Always use either

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper inter- pretation of these symbols wi

7SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualied service technician. For service we sug

8ELECTRICALEXTENSION CORDSUse only 3-wire extension cords that have 3-prong ground-ing plugs and 3-pole receptacles that accept the tool's plug.

9GLOSSARY OF TERMSPush Blocks (for jointer planers)Device used to feed the workpiece over the jointer planer cutterhead during any operation. This a